|
|
1,500 - 7,200 GPD
| STANDARD
FEATURES: |
| |
|
| • |
1.5 cu. ft. Maxi-Cure w/auto backwash |
| • |
5 micron pre-filter |
| • |
Multi-stage booster pump |
| • |
Thin film composite membrane |
| • |
PVC membrane housing
|
•
|
Adjstbl. waste & recycle needle valves
|
•
|
Product & waste flow meters |
•
|
1 HP s. s. repressurization pump w/10
gallon pressure tank |
| • |
Two 20" GAC carbon block post-filters |
| • |
Pre and post-filter gauges |
| • |
System PSI gauge |
•
|
Stainless steel 24gpm ultraviolet water sterillizer |
| • |
Stainless steel pre-treatment jackets |
| • |
Marine-grade back panels |
| • |
powder-coated steel frame w/casters |
•
|
Two 300 gallon polyethylene storage
tanks w/adaptors |
|
 |
| |
|
| • |
Off/On switch |
| • |
Fused power |
| • |
Time delay |
| • |
UV light switch |
| • |
Repress. switch |
| • |
Hour meter |
| • |
Off delay |
| • |
Dual level controller (R.O) |
| • |
Dual level controller (repressurization) |
| • |
Automatic hourly flush |
| • |
Motor contractors |
| • |
TDS monitor |
| • |
System control switch |
| • |
Low pressure switch |
| • |
Pre-treat lock-out |
| • |
Low press. off delay |
| |
|
| |
|
|
Mini-Filtration Station |
STATUS LAMPS:
power, running, flushing, low pressure,
tank full, pre-treat lock-out, low level
POWER REQUIRED:
220v/60hz, 30 amp, 1 Ø or
220v/60hz, 15 amp, 3 Ø
|
FEED WATER PARAMETERS:
 Temperature
85°F maximum Pressure
40 - 80 psi maximum TDS
2000 ppm maximum. If higher, consult factory Iron
tolerence 0.5 ppm maximum Hydrogen
sulfide must be removed
Silica
tolerance can not be higher than 125 ppm in the concentrate stream.
Anti-scalant should be considered for any levels over 75 ppm. Turbidity
should be removed
Hardness over
10gpg should be softened.
OPERATING PARAMETERS:
Operating pressure
200 psi maximum Water
recov-ery is facotry set at 33 - 35%
pH range 3
- 11 Flow rates
are determined by the membrane mfgr's. testing criteriea of 1500
ppm Nacl solution, 77F water temperature, 225 psi at 10 - 15% recovery.
Actual flow rates may vary depending on the pre-treatment used,
water conditions, system size and applied pressure.
|
| MODEL |
GPD
|
MEMBRANE
|
MOTOR
|
DIMENSION
|
|
|
Size
|
QTY
|
|
|
|
| MFS-1 |
1500 - 1800
|
4" x 40"
|
1 ea.
|
1 HP
|
60"L x 34" x 78"H
|
850 lbs.
|
| MFS-2 |
3000 - 3600
|
4" x 40"
|
2 ea.
|
2 HP
|
60"L x 34" x 78"H
|
850 lbs.
|
| MFS-3 |
4500 - 5400
|
4" x 40"
|
3 ea.
|
2 HP
|
60"L x 34" x 78"H
|
850 lbs.
|
| MFS-4 |
6000 - 7200
|
4" x 40"
|
4 ea.
|
3 HP
|
60"L x 34" x 78"H
|
850 lbs.
|
|
